Today to share the knowledge of mini crystal wireless charging, which will also explain the mini wireless charger, if you happen to solve the problem you are now facing, don't forget to pay attention to this site, start now!
< ul>1. Mercury router Wireless bridge setting method: Connect the WiFi of Mercury router in advance. Enter the URL melogin.cn to set up the router in your mobile browser. Then set the router login password and click the arrow below. Then set the wireless name and wireless password, click the right arrow. Once moreJust connect to this WiFi.
2. Enter melogin.cn or 19161 to login to the Settings screen of the MAC1200R router. Click "Advanced Settings". Click on "Wireless Setup 4G" -- "WDS Wireless Bridge". Click "Next". At this point, the Mercury MAC1200R router will automatically scan for nearby wireless signals, please find the wireless signal of the main router in the result - then click "Select".
3, click "Advanced Settings" -- "wireless Settings" -- "WDS wireless bridge" option to open the water firstIn the right "WDS Networking Wizard" page, directly click "Next" Mercury router Wireless bridge setting 1 (3), at this time, Mercury router will automatically scan the nearby wireless signal, as shown below.
4, enter the setting interface of the main router, and then click "Running status" in the left option bar, you can find the DNS server in the WAN port status bar, there are two, primary DNS and alternative DNS server, record it.
5, click "Internet Settings" -- "Internet mode" select: automaticGet the IP address - click "Save". The second Mercury router, set to automatically get an IP address online attention: the old Mercury router, you need to click "network parameters" - "WAN port Settings" - "WAN port connection type" to select: dynamic IP, as shown in the figure below.
6, first set the LAN IP address of the main router, the DHCP server is turned on, and the IP address allocation range is 19162 to 1916254. Set the WIFI access password. Note that the encryption mode of all routers is the same. WPA2-PSK mode is recommended. Pay attention to the WIFI channel Settings, because all routers will be set on the same channel, go back to the router information and record the router's WAN MAC address.
Take the crystals to the sink and rinse them under the water for 1 minute, gently scrubbing them with your fingertips. Wash the crystal before charging, so you can absorb more energy. If the crystal is too large or bulky to carry under the faucet to rinse, you can create a single frequency of sound nearby-10 minutes, such as tapping a tuning fork or qing, to purify the crystal by sound.
Living water cleaning method: open the faucet in your own home (the effect of water purifier is better), put the crystal into a small dish, rinse your crystal for about ten minutes, and put it in the sun or cool place to dry naturally after washing, so that the crystal can also be effectively purified.
This crystal cleaning method can be done every day, as long as the crystal stone is put into the crystal cluster when you are not wearing the crystal, you can keep charging the crystal. (2) If natural crystal clusters can be purchased to purify crystals, better results can be achieved. (9) Natural cleaning method: cleaning sideMethod: As long as the crystal is placed in the countryside, let the quiet and harmonious sound of nature purify the magnetic field of the crystal, and this cleaning method can increase the energy of the crystal.
Crystal cluster degaussing method The crystal cluster itself has a strong energy, so it can be used to degaussing and charging topaz. Simply place topaz on the cluster overnight.
First wash the crystal worn with water, and put it in the sun when the sun is strongest between 11:00 and 13:00 at noon. In that case, only half a day is enough! But beware: some strapsInstructions
1. The manual for using the authentic Mini 1000 mah solar charging bank is as follows: Use the original accessories to charge, pay attention to the size of the charging current, and pay attention not to overcharge. In order to extend the service life of the charging bank, the first time you use it, put all the power, and then charge with the original power cord when the red light is displayed, charge to the full state, and the green light is displayed. Do this three times in a row and then recharge. After the fourth time, it is not necessary to discharge the power completely.
2, wait for the charging bank to complete charging 01 Read the instructions and find the estimated charging time. Avoid power banks and electricitySource timeout connection. The instructions on the product should have an approximate time for charging. Most power banks recharge in one to two hours. 02 Unplug immediately after charging. Check the charging status periodically during charging. Once all the LED lights are on, disconnect the power bank and the power supply immediately.
3, the new machine is recommended not to rush to charge, the normal use of electricity to the screen prompts 10% need to charge. Then shut down, shut down and charge once. The first time the new machine is best to use electricity, it is recommended not to use up, the new lithium-ion polymer battery, different from the old battery, no memory effectYes. Plug the cable into the mini charging port first, and then plug the two-hole plug into the socket.
4, indicates the percentage of the remaining electricity in the total electricity. Each LED represents 25%. If only the first one lights up, it means that 25% of the battery remains. If three lights up, it means 75% remains. For charging, some are all bright, no longer flashing, indicating full; Sometimes the last LED flashes and the sign is full. The full charge identification of the mobile power supply should be based on the manual of the mobile power supply purchased.
The introduction of mini crystal wireless charge will talk about it here, thank youYou take the time to read the content of this site, more information about mini wireless chargers, mini crystal wireless charging don't forget to find on this site.