Today to share the knowledge of water-cooled wireless radiator disassembly video, which will also explain how to plug the water-cooled radiator, if you happen to solve the problem you are now facing, don't forget to pay attention to the site, now start!
< ul>Because the regulating cap of the regulating valve is generally aliveJoint, so only need to use a wrench or pliers to remove the live joint, and then remove the adjustment cap, because its temperature control valve is directly connected to the pipe, so must cut off the pipe thread joint on the pipe. After removing the temperature control valve and replacing the valve, another PPR thread joint can be welded, but at the time of disassembly, the heating company staff or professionals operate.
can be taken down, but take down and can not directly solve the problem of heating is not hot. The sensitivity of the temperature control valve is not enough, which will lead to problems in temperature regulation, because the temperature control valve will not automatically adjust the indoor temperature due to temperature difference changes. So take it down andCan not solve the problem of floor heating is not hot.
The installation method of the radiator temperature control valve is as follows: First, install the valve body at the entrance of the radiator, ensuring that the arrow indicates the correct direction. In order to facilitate the installation of the thermostat, the handle should be set in the maximum open position (number 5 position) before installation, and then screw the locking screw of the thermostat to the valve body. In order to avoid functional failures caused by welding slag and other debris, pipes and radiators need to be thoroughly cleaned.
Radiator thermostat In most of the old radiator heating systems in China, the use of up and down through the vertical type>Place the heat sink over the installed CPU, and ensure that the four mounting holes on the mainboard match the four screw holes on the heat sink. Using a Phillips screwdriver, lock each screw tightly and attach the radiator just enough to the motherboard. Then fasten the screws in a staggered sequence (as shown in the figure below) to ensure that the contact surface between the heat sink and the top of the CPU is evenly and completely tight.
The buckle on the back of the mainboard is different from the buckle shown in the following figure. The buckle needs to be installed on the back of the mainboard to help secure the CPU water-cooled heat sink installed on the front of the mainboard.As shown in the following figure, the left side is Intel platform buckle, and the right side is AMD platform buckle. When purchasing a water-cooled radiator, these two sets of buckle are given as a gift at the same time, and the business is mainly to be compatible with the two platforms.
Installing a water-cooled heat sink Secure the water-cooled heat sink to the CPU slot on the mainboard. If there is no professional pond mat, it is necessary to apply a layer of moderate thickness lubricant on the CPU to connect the wires and pipes to connect the pump and radiator, and connect to the power system to ensure its stable operation. The hose is then connected to the radiator and water pump, and finally to the faucet.
, bendPipe (hard pipe bending), water cooling liquid. The procedure is as follows: Install the CPU water cooling head and cold bar, measure the distance between the two connection ports, and screw the head. When locking the screw head, remember to insert the rubber ring, plug in the hard tube and design a water outlet for cleaning and replacing the water cooler. Start to inject water cooling liquid. It is recommended to place paper towels at each interface and observe whether leakage occurs.
Install the water-cooled radiator: (1) First, install the buckle of the water-cooled radiator on the back of the motherboard, and install the corresponding screw holes according to the CPU slot type (775771150, 1156)After the fixing screw is installed, the motherboard can be installed inside the chassis. (2), the next is to install the CPU water-cooled radiator on the front CPU of the motherboard. < / p > < p > modern water-cooled radiator have excellent compatibility, can usually be compatible with Intel and AMD mainstream platform, such as: Intel platforms: including LGA201LGA136LGA115LGA115LGA1150 interface. AMD platforms: FMFMAM3, AMAM2, AM2, etc. Installation steps are crucial depending on your CPU model and platform type, such as InThe subtle differences between tel and AMD will determine the correct installation of the radiator.
1, One plus liquid cooling radiator series of new products, magnetic wireless charging is its carefully built flagship. The packaging design is consistent with ONEPLUS's style, with the main color of red complementing the simple OnePlus logo. Open the package, the eye is a liquid cooling radiator body, operating instructionsAnd warranty card, simple and professional. The design concept of OnePLUS magnetic wireless charging also focuses on practicality and aesthetics.
2, Real me GT2 master exploration version first equipped with the first generation of Snapdragon 8 flagship chip processor, Real me first LPDDR5x memory chip and a new generation of X7 unique display chip, 7-inch top OLED straight screen, double VC liquid cooling MAX system, 100W light speed second charge 5000mAh battery, X-axis motor and 50MP dual main camera and other flagship configuration, can be called my annual texture flagship.
1. Take a full picture and see what type of radiator it is. Looks like you need to remove the fan first.
2, the notebook radiator, fixed by two to four screws, after unscrewing, the radiator can be removed, the cpu is exposed, there is a word plastic screw above the cpu, after screwing, the cpu can be taken down. Desktop computer scatteredThe heater generally has a buckle, the buckle is opened, the radiator is taken down, and the cpu is leaked. There is a circlip on the side of the cpu, which can be bounced open when pressed, and the cpu can be easily removed.
3, you can take it off, but it requires brute force and skill. Remove the gasket with card on the screw post (see red circle below), then it is easy to remove the screw. Take the gasket skill, if you do not want to recover, you can directly destroy the pad money; If you want to recover, the shrapnel on the inside of the gasket stuck to the screw column is pulled outward one by one until it can be removed from the screw column.
4, remove the heat sink, we can seeTo the fan. The fan is usually fixed to the heat sink by two or four setting screws. We need to loosen these screws with a screwdriver and gently remove the fan. Some fans also have a plug to connect to the power supply, we need to unplug this plug first, and then remove the fan. Cleaning the CPU fan After removing the CPU fan, we can clean it.
5, the steps to remove the CPU fan are as follows: First, open the computer host case, find the two screws behind the main case to fix the side cover of the main case, use a Phillips screwdriver to unscrew it, and then directly pull it out. When you open the main boxYou can see the computer motherboard, and then find the four bolts used to fix the CPU fan, the position is around the CPU fan, you can use a flat-head screwdriver to remove the fixing bolts at the four corners of the cpu cooling fan.
About the water-cooled wireless radiator disassembly video and how to plug the water-cooled radiator this is the end of the introduction, do not know you find the information you need? If you want to know more about this, remember to follow this site. < / p >