This article gives you a talk about how to charge SF wireless lamp, and the corresponding knowledge points of SF charging, I hope to help you, don't forget to collect this site. < / p > < h2 > the article directory list: < / h2 > < ul > < li style = 'margin - bottom: 3 px; list-style: none'>1, Wireless charging desk lamp how to iphone charging
1, as long as your phone supports wireless charging, put in the middle of the "cross symbol" position can immediately start charging, at this moment, you will see the dynamic aperture of charging appears, convenient and simple! Sweet thing is, when the phone's battery is at 90%When this happens, it slows down the direct flow of current, thereby extending battery life.
2, this kind of music desk lamp generally can not give mobile phone wireless charging, now wireless charging words only that kind of small disc, like you this kind of music desk lamp it must still need a line connection, there is no connection then it must be that, well, there is not much of the role, so you still need to pass a certain connection. Technology that uses magnets to charge devices.
3, this kind of music desk lamp generally can not wireless charging mobile phones, now wireless charging words only that kind of small disc, like you this kind of music desk lamp it must alsoSpecifically, you can look at the information above the manual.
up to 3 hours. According to the query of China audio network shows that there is a small capacity lithium battery inside the small audio, the charging current is not much at the design time, for 0.2 amp, and the charging of the Bluetooth small speaker takes 2 to 3 hours.
If the lamp is charged, it may take 8-10 hours to be full, and if it is used while charging, it can be full in about 4 hours. The charging of the lamp should be careful not to take too long, as long as it is fully charged, the power should be turned off, because it will not be charged to the battery after full charge, and notTurning off the power can also cause damage to the battery.
Now most of the batteries in the speaker are lithium batteries, a few are also useful lead-acid batteries, as long as it is full to 100%, it is okay, battery use and maintenance, no special requirements, but pay attention to one point, do not over-discharge, over-discharge has the greatest impact on battery life.
Most commonly used electric boards are 600mAh to 750mAh. The output current of the charger is not as large, from 200mA to 1000mA. The output current of the charger is 200mA, charging for about 6 hours, 250mAbout 5 hours for A, about 4 hours for 300mA, and about 3 hours for 500mA. 700mA for two hours.
As long as your mobile phone supports wireless charging, you can immediately start charging in the middle of the "cross symbol" position, at this moment, you will see the dynamic aperture of charging appears, convenient and simple! The sweet thing is that when the phone's charge reaches 90%, it will slow down the direct current, thereby extending the battery life.
The method of use is as follows: After plugging in the power supply, touch the curved light pole with your finger at any position to light the light. Put the device that needs to be charged under the lamp, switch the mobile phone to the wireless charging mode, and put it into the wireless charging induction area of the lamp. Use the phone charging cable to connect the lamp USB port to the phone, and the phone can also be charged.
LED wireless charger Bluetooth speaker to charge the mobile phone method is as follows: ensure that the speaker is connected to the power adapter, the speaker itself is fully charged. Find the wireless charging area on the speaker, on the top or side. Place the mobile phone that supports wireless charging on the wireless charging area and ensure the back of the mobile phoneThe part is in contact with the charging area.
Connect the standard charger and data cable of the mobile phone to the wireless charger, and then put the mobile phone in the center position of the left and right of the wireless charger base, you can realize wireless charging, the indicator light will have a breathing effect, 5 seconds later, plug and play, convenient and quick.
Extension: Open wireless reverse charging method: You can enter the phone Settings -- battery -- more Settings -- open the "wireless reverse charging", after opening the peripheral can provide up to 10W charging power supply urgent charging. Note: After this function is enabled, if there is no charging for other devices for a long time, it will automatically turn off;This function cannot be enabled when the battery battery is less than or equal to 20%.
Methods for wireless charging a mobile phone (Huawei mate40 is used as an example) are as follows: Operating environment: Huawei mate40, HarmonyOS0, and Settings. First, we open the Settings option and click Battery. Step two, we click on wireless reverse charging. The third step, put the device that supports wireless charging on the back of the machine, you can wireless charging.
SF wireless charging table lamp how to charge it here, thank you for taking the time to read the content of this site, more about SF charging, SF wireless charging stationHow to charge the light information don't forget to check the site oh.