1, the mobile phone uses wireless charging, you need to buy wireless charging base or wireless charging back shell can be used. Connect the charger to the wireless charging base, and then place the phone or a phone with a wireless charging back case on the wireless charging base. Take off the holster If the phone's holster is too thick or not the original charging holster, it may affect the charging effect, it is recommended to take off the holster and try charging.
2. In addition to supporting super wired fast charge, some high-end mobile phones of Huawei can also support wireless charging, and wireless charging needs to be purchased separatelyLine charger. How to use Huawei wireless charger? Connect the charger (the charging tip that came with your phone or was purchased separately) to a power source. Connect the data cable Connect the charger to the wireless charger using the data cable. Place the phone Place the rechargeable area of the phone in the center of the upper surface of the wireless charger, and the phone shows that it is charging.
3, the correct use of wireless charger: Connect the charger to the power supply. Please use the charging head, charging cable and wireless charging base purchased by yourself. Place the charger on a horizontal surface or other location suggested by the manufacturer. Place the phone on the charger so that the screen is facingLine charger small light is not on what happened '> Wireless charger small light is not on what happened
1, then you can first back up your important data and the required data and then restore the factory Settings, and then try, if not, it may be poor contact or the phone is not suitable.
2, according to the title of the main description, this situation is generally the charging treasure battery no power, the circuit board to the battery protection caused by no voltage output, under normal circumstances, fully charged charging treasure, press the power button, the four lights will be on, after a while will be extinguished. It is recommended to charge the power bank first and then tryWhether you can charge your phone.
3, the internal battery is too low, did not charge in time. The output jack or output cable is faulty. The mobile power supply itself is faulty.
4, there are roughly two reasons for the fault: the power switch of the charging bank is faulty. You can short-circuit the two pins of the switch to check whether the indicator light can light up normally. If it can light normally, it indicates that the key switch is damaged and can be replaced. If no, the fault is in the subsequent circuit. The booster plate is faulty. The detection of the booster plate fault can only be measured by a multimeter.
5. The power switch of the charging bank is faulty. If the charging lamp of the charging bank is not on, it is possibleIt's caused by a faulty power switch. Can be a simple trick, short switch two pins, see whether the indicator light can light up normally. If it is lit, it means that there is a problem with the key switch, and a new one is on the line; If it still doesn't light up, the problem could be in a subsequent circuit. If the charging lamp of the power bank is not on, it may be caused by the fault of the booster board.
2, wireless charging refers to the charger on the terminal device that needs to be charged without the traditional charging power cord, using the latest wireless charging technology, through the use of the magnetic field generated between the coils, the magic transmission of electrical energy, inductive coupling technology will become a bridge connecting the charging base station and equipment. How to use: Connect the USB cable and plug it into the socket.
3, mobile phone wireless charging refers to the connection between the charger and the electrical device without wiresYou can charge your phone.
Sanxiong Aurora pakled night light alarm clock can be set using the button above the table lamp. Pak Sanxiong Aurora Night Light is a desk lamp with alarm clock and time and mobile phone wireless charging.
The method of turning off the alarm clock of the Bluetooth speaker is as follows: First, press and hold down the M key in the state of the speaker until the sound of "drip drip" is emitted, indicating that the setting mode is entered. Then press the "M" key until you reach the speakerIf the Time tone is played, the alarm is set. Next, press the "" key or" - "key at the top of the speaker to select the alarm number to turn off.
Call you to sleep and get up "sleep" function: iphone7 comes with the alarm bell everyone should know how noisy, and only monotonous beep sound, every morning is really listen to the head, the main thing is that the custom ringtone is not as convenient as Android, very troublesome. So recommend this bedtime function, we can go to the clock app, turn on the bedtime "reminder function.
About Bear wireless charging night light how to charge and noThis is the end of the introduction of the line charging night light, do not know you find the information you need? If you want to know more about this, remember to follow this site. < / p >