Today to share the knowledge of how to connect the desktop wireless audio, which will also explain how to connect the wireless audio to the computer, if you happen to solve the problem you are now facing, don't forget to pay attention to the site, start now!
< ul>1, the mobile phone standard charger and data cable connected to the wireless charger, and then the mobile phone is placed (vertical) or horizontally in the wireless charger base left and right center position, you can achieve wireless charging, the indicator light will have a breathing effect, 5 seconds after the extinguish, plug and play, convenient and quick.
2, the mobile phone uses wireless charging, you need to buy wireless charging base or wireless charging back shell can be used. Connect the charger to the wireless charging base, and then place the phone or a phone with a wireless charging back case on the wireless charging base. Remove the case if the phone's case is too thick or not the original charging caseMay affect the charging effect, it is recommended to take off the holster after charging attempt.
3, the correct use of wireless charger: Connect the charger to the power supply. Please use the charging head, charging cable and wireless charging base purchased by yourself. Place the charger on a horizontal surface or other location suggested by the manufacturer. Place the phone on the charger with the screen facing up. For best performance, place the phone in the center of the charger or in the location recommended by the manufacturer.
4, HONOR 100pro wireless charging how to use I think HONOR 100pro wireless charging can be used like this:Place on a smooth surface. Place the phone on the charging area. Make sure the phone is in contact with the wireless charger. Plug the charger into the socket.
5. If your Huawei mobile phone supports wireless charging, place the mobile phone screen facing up in the center of the charger or the position suggested by the manufacturer after the wireless charger is powered.
Audio and microphone connection steps: Insert the receiver line into the output hole on the receiver and connect to the microphoneThe same as in the air. Put the other end into the amplifier microphone audio port, the audio port will generally have a note here need to pay attention to check. Plug the power cord into the wireless receiver. Plug the other end in. Install the microphone battery, pay attention to the positive and negative terminals, the small end to the large end.
Uhf wireless microphone The method of connecting the sound is as follows: Uhf wireless microphone consists of a transmitter and a receiver. Transmitter [audio output port] is mainly used to connect the SLR, and other audio equipment, including audio equipment. uhf wireless microphone mainly includes transmitter and receiver, transmitter [audio output port] mainlyUsed to connect SLRS, and other audio device receivers, mainly to connect external audio devices.
Plug the wireless microphone receiver into the computer's sound card or separate sound card, and the speaker is connected to the computer's or separate sound card's speaker output. The receiver of the wireless microphone is connected to the microphone jack of the speaker or power amplifier. The wireless microphone is matched with the receiver, the receiver is installed in the audio, no connection line, the audio is opened, the microphone switch is opened on the line. First you need a power amplifier and a sound mixer.
Turn on the power to the wireless microphone and stereo, and ensure that they are in placeIn normal working condition. Find the Pair or Connect button on the wireless microphone and press it to initiate the pair mode. Find the Bluetooth or wireless Settings option on your stereo and go to that setting. In the list of available devices, locate and select your wireless microphone.
To connect the wireless microphone to the connected sound, you need to use the audio connection line to connect the audio output of the wireless microphone receiver with the MIC input of the sound. There is no sound after the wireless microphone is connected to the stereo, there are two cases. The first step is to insert the receiver wire into the output hole on the receiver, as shown in the figure belowAs shown.
First, insert the receiver wire into the output hole on the receiver, as shown in the figure below. Then, connect the other end to the power amplifier microphone audio degree port, the audio port will generally have a note here need to pay attention to check, as shown in the following figure. Next, plug the power cord into the wireless receiver and plug the other end into the power supply, as shown in the picture below.
1. Connect the charging head and the charging base with the data cable, and then insert the charging head into the power supply. Charging basePlace the seat on the table, and place the phone screen facing up in the center of the charging base. After the phone is placed on the charging base for a few seconds, there is a "drip" sound, indicating the start of charging. If you use the super fast charging head and Super fast charging base, the charging base will use the super fast charging mode to charge the phone.
2, after the wireless charger is powered, directly place the phone screen facing up in the center of the charger or the position suggested by the manufacturer to charge. If your Huawei mobile phone supports wireless charging, place the mobile phone screen facing up in the center position of the wireless charger or the position recommended by the manufacturer after the wireless charger is powered onGo to the computer Settings screen and select the option to add Bluetooth or other devices. Click to enter, in the page of device type, select the option of Bluetooth to enter. Take out our Bluetooth speaker device, turn it on and adjust it to Bluetooth pairing.
Connect a power port to the USB port on the computer host. Tap the Bluetooth icon on your computer. Click Add Device on the page that appears. On the Add Device page, click Add Bluetooth or another device. Click on the Add Device TAB and select Add Bluetooth. The computer will automatically scan the stereo that has Bluetooth turned on, and then click the scanned soundRing the name.
Bluetooth icon in the lower right corner of the desktop -- right-click -- Add device. Select the found Bluetooth speaker and click Next. The computer automatically installs the driver and displays that the device was successfully added. Install Driver Start menu - Click Devices and Printers. Find the Bluetooth speaker, select it, and right - click Properties. Switch to the Services TAB, you can select all the options, and then confirm, the computer will automatically install the driver.
Operating device: Dell computer operating system: win10 Operating software: Bluetooth speaker First step, open Bluetooth speaker wait, openThe Bluetooth speaker will tell you that Bluetooth is on. Step 2, Open the computer at this time and find the Settings. The third step, click select Bluetooth Settings to add the device, you can see the Bluetooth device name, wait for the connection success. Step 4, when it shows that the pair has been paired, it proves that the connection was successful.
Open [Start] in the lower left corner of the computer, and click [Settings] to enter the Windows Settings. Find [Bluetooth] under [Device] and click [Bluetooth] to enter the next interface. At this time, the Bluetooth and other devices interface will pop up, turn on [Bluetooth], and then click [Add Bluetooth or other devices], and a small window will pop outMouth.
About the desktop wireless audio how to connect and wireless audio how to connect to the computer this is the end of the introduction, do not know you find the information you need? If you want to know more about this, remember to follow this site. < / p >