Self-made wireless charger 1: External module installation Procedure Attach the module to a place far from the MicroUSB interface. Step Connect the MicroUSB or Lightning port on the module to the phone. Steps If there is double-sided tape on the receiverYou can glue it directly to the back of the phone. If it doesn't come with it, you have to figure it out yourself. Step to select the most appropriate position, be careful not to let the part of the connection line warped phenomenon.
You can buy a wireless charging receiver, stick it on the back of the mobile phone or insert it into the mobile phone charging port, the advantage of this method is that the cost is low, there is no need to replace the mobile phone or dismantle the internal phone, the disadvantage is that it may affect the beauty and feel of the mobile phone, as well as increase the wear and tear of the charging port.
First cut the USB charging cable into two sections not far from the two ports. Glue the ends of the two wires with scissorsSeparate out a section to screen and then cut off the green line with the bottom line generally complex. Use hot glue to attach the magnet to the charger. Wrap the wires in the USB with tinfoil. Then wrap the wires and roll them up with copper wire. The USB cable with the copper wire rolled up is then wrapped in electrical tape.
To add wireless charging function to ordinary mobile phones, the most critical is to install a wireless charging receiver. This process usually involves opening the case of the phone, finding where the battery or battery is connected, and welding or connecting the receiver to the appropriate circuit. This requires a certain knowledge of electronics and fine manual skills as handsThe phenomenon of.
2, to add the wireless charging function to the ordinary mobile phone, the most critical is to install a wireless charging receiver. This process usually involves opening the case of the phone, finding where the battery or battery is connected, and welding or connecting the receiver to the appropriate circuit. This requires a certain amount of electronic knowledge and fine manual skills, because the components inside the phone are very small and fragile.
3, the self-made mobile phone wireless charging method is as follows: Prepare materials: The mobile phone charger first cut the USB charging cable into two sections not far from the two ports. Glue the ends of the two wires with scissorsSeparate out a section to screen and then cut off the green line with the bottom line generally complex. Use hot glue to attach the magnet to the charger. Wrap the wires in the USB with tinfoil. Then wrap the wires and roll them up with copper wire.
4, the first step, we open the Settings option, click the battery. Step two, we click on wireless reverse charging. The third step, put the device that supports wireless charging on the back of the machine, you can wireless charging. The basic principle of wireless charging: electromagnetic induction of a certain frequency of alternating current in the primary coil generates a certain current in the secondary coil through electromagnetic induction, thereby transferring energy from the transmission end to the receiving endEnd.
5, wireless charger usage: the mobile phone standard charger and data cable connected to the wireless charger, and then the mobile phone is/horizontal in the wireless charger base left and right center position, you can achieve wireless charging, the indicator light will have a breathing effect, 5 seconds after the extinguish, plug and play, convenient and quick.
6, first click the "Settings" option on the desktop of the phone. Then in the Settings page that opens, click on the "Battery" option. Finally, in the battery page, open the "wireless reverse charging switch". The benefits of wireless charging of mobile phones do not need to plug and unplug, convenient and fast. Just leave the phone chargingOn the device, you can start charging, don't worry about finding the data cable or plug. At the same time, it can protect the phone interface and extend the service life.
ready-made. Charging base, charging back sticker, charging head or charging treasure, charging line, assembled, can be wireless output wireless input, still can be wired charging; Wireless charging waste electricity is certain, slow charging, low efficiency, heat, can not be separated from the base.
If there is double-sided tape on the receiver, you can glue it directly to the back of the phone. If it doesn't come with it, you have to figure it out yourself. Choose the most suitable position, be careful not to let the part of the connection line have the phenomenon of warping. Then you can put the phone on the wireless charging dock to experience the wireless charging function. The next task is to bringThe receiver's metal shock is connected to the smartphone battery, which is the most difficult part of the process.
Today bought a box of a broadcast steak, 148,18 packages of steak, thin poor, 148 cut beef also want to cut a big piece of it... . Third, drones. Saw a drone on a certain patch, watched their video felt very good, and the price is not expensive to buy a model. Buy back to try, this is not a drone, this is a remote control car. Running on the road, not flying.
Sweeping robot In fact, my attitude toward sweeping robots has beenIt is still relatively "cold", after all, I bought a sweeping robot that crashed everywhere before, and the experience is really not much good. But some friends use the sweeping robot is still very suitable, such as when there is no one at home after going out, you can use it to sweep and mop the floor.
This is the end of the introduction of self-made remote wireless charging and 12 meters remote wireless charging production, do not know you find the information you need? If you want to know more about this, remember to follow this site. < / p >