The reason why the car charger is not charged is: the voltage is unstable when charging, resulting in no charging. When charging, mobile phones or other smart electronic products generally open charging monitoring and detection procedures. If programWhen the vehicle charging voltage is detected to be unstable, it is forbidden to charge. When using the seat, there will be no program for detection, it is recommended to use the usb interface of the car audio computer system to charge, whether it is a line or a seat.
The position is incorrect. Millet 11 wireless car charger does not respond, is the location of the phone is not correct, you can adjust the position of the phone on the wireless charger, or the wireless charger hardware is damaged, conditions can try to use other support wireless charging mobile phone try.
A charger that is not suitable for the power of the phone will damage the battery of the phone. Among them, wireless charging technology comes from radio energy transmissionTechnology, low-power wireless charging is often used electromagnetic induction, high-power wireless charging is often used resonance. The power supply device transmits energy to the electrical device, which uses the received energy to charge the battery and at the same time for its own operation.
Mi 6 does not support wireless charging, so Mi wireless car charging, your Mi 6 is not available. You can contact customer service, seven days no reason to return. Because it was your mistake that caused the return, you need to pay for the return postage yourself.
If the indicator blinks, the charging status is abnormal and wireless charging cannot be performedThe following exceptions: The mobile phone is not compatible with the wireless car charging protocol. The phone does not support wireless charging.
1, millet wireless car charger can only tighten a certain total width of the mobile phone, if the owner's mobile phone is relatively narrow, it is likely to clip too loose, resulting in intermittent charging. It can replace the small wireless network car charger, and it can also put the mobile phone shell on the mobile phone shell to try whether the mobile phone can tighten up a little. It may be that the iron clamp force of the car charger itself is insufficient, or the product quality of the car charger itself appearsQuestion.
2, millet wireless car charger can only tighten a certain width of the mobile phone, if the rider's mobile phone is relatively narrow, it may not be tight, resulting in intermittent charging. You can replace a small wireless car charger, you can also put a phone case on the phone, and try to tighten the phone a little. It may be that the clamp force of the car charger itself is not enough, or the car charger itself has quality problems.
3, the power adapter is faulty or the charging line is damaged, you can try to replace the power adapter and the charging line to see if there is still a problem. Poor contact inside the charging port or battery aging will also leadCause intermittent charging. If the problem still exists after replacing the power adapter and charging cable, it may be necessary to replace the motherboard or repair the charging port, it is recommended to consult a professional after-sales maintenance center.
4, the principle of car wireless charging base is magnetic field charging, the closer to the middle area, the better the magnetic field strength, if in the edge position, the magnetic field is weak, and even can not activate the mobile phone wireless charging function, resulting in intermittent, or can not charge. So please try to put the phone in the middle position when charging, or change a larger phone case, add some decorative pieces, etc., to ensure that the phone is in the middle position, it should be OK. hopeThere may be water vapor, resulting in a slight short-circuit of the motherboard. 2, the mobile power motherboard in the process of boosting the sound, but the sound is usually very small, almost inaudible.
2, personal think and charging equipment, millet 80W wireless charging base built-in cooling fan, charging the default open speed wireless charging mode (feel the noise can be manually closed), we can hear the fan in the process of charging "buzz" sound, hand near the bottom of the wireless charging base, can also feel the cool wind blowing out of the fan. I hope I can help you.
3, and current electricityPressure matters. The constant sizzling sound comes from the inductor coil inside the mobile power supply. The mobile power supply needs to start the inverter circuit when the inverter circuit works to produce a certain frequency of alternating current, which belongs to the audio range, and needs to be converted by the inductor coil, under the action of the larger current, the coil will vibrate, and the generated sound will be transmitted, so there is a small squeak.
4, click the phone Settings page, select sound and vibration, and then select advanced sound Settings, you will see the system sound and vibration keys. After clicking, turn off the charging sound effect.
5, after inserting into the car, there will be a circle of white lights around. Before driving 20 minutes, the power can basically remain good, and now the use of millet car charger effect is very good, can be filled with tens of percent of the power, as the original fast charge. Millet (MI) wireless car charger car wireless charger work is also very fine, the top is also equipped with a cooling fan, summer can automatically heat.
6, first of all, the light of the millet wireless charger will blink when it starts charging, which is a normal phenomenon. But if the light keeps flashing, it may be caused by the following reasons: The distance between the charger and the phone is too far. Xiaomi wireless charger needs to fit with the phone to charge normally, if the distance is too far, the light will always flash. The charger port is loose.
Xiaomi car wireless charging, charging will certainly be hot, and it is still wireless fast charging, many people have this problem, but there is no official solution. Avoid exposure to the sun and direct sunlight. If too hot, do not continue to use, safety first.
is not original. Although wireless charging is very compatible, it is also very particular about cooperationXiaomi wireless charging is tailored for Xiaomi mobile phones, even in the transmission protocol, power above can achieve the ultimate cooperation, wireless charging overheating, because it is not the original adaptation, the use of original adaptation, in order to ensure the charging speed at the same time, but also better control the heating phenomenon during the charging process.
The reason why the air conditioning port of Xiaomi wireless car charging and discharging is hot is that the line is faulty. According to the query of relevant public information, when the millet wireless car charging line fails, it is very easy to heat, the temperature is high, and it is easy to produce security risks.
1, charger failure, replace the charger; The charging port contact is poor, clean the charging port in time. Millet 13 charging intermittent due to millet 13 charger failure, charger failure led to unstable current and voltage, resulting in intermittent charging, you can replace millet 13 charger. Millet 13 charging intermittent because the charging port contact is poor, resulting in the current can not operate normally, you can clean up the charging port in time.
2, charger, data cable failure, battery aging, mobile phone system problems. Charger, numberAccording to cable failure: the charger and data cable are damaged and aging, which will lead to intermittent charging. Battery aging: Battery use time is too long, there will be intermittent charging situation. Replace the battery. Mobile phone system problems: Sometimes, the mobile phone system problems can also cause intermittent charging. You can restart the phone and update the system.
3, millet 13 charging intermittent reasons may have the following: power adapter failure or charging line damage, you can try to replace the power adapter and charging line to see if there is still a problem. Charging port internal contact is poor or battery aging, alsoWill cause intermittent charging. If the problem still exists after replacing the power adapter and charging cable, it may be necessary to replace the motherboard or repair the charging port, it is recommended to consult a professional after-sales maintenance center.
4, charging cable or charger failure: if the charging cable is not firmly connected, or the charging cable itself is broken or damaged, it will lead to frequent disconnection of the phone during the charging process. If another brand or model of adapter is used for charging, it may cause an unstable power supply situation, resulting in repeated disconnection and connection of the phone. Workaround: Try replacing it with a new charging cable and official adapter, and make sure it's connectedSolid.
5, reason 1: The charger failure charger does not match: the voltage and current of the millet phone charger are required, if the use of a mismatched charger, it will lead to a rush and a stop. Charger damage: If the charger has been impacted or used for a long time, there may be damage, resulting in unstable charging.
6, it may be that the charger and data cable are partially damaged, check the charger and data cable, if there is damage, it needs to be replaced in time to avoid greater losses. Check the phone connector for the presence of foreign objects by using tools such as cotton swabs and alcoholClean it up. It may be that the mobile phone battery is damaged, and it needs to be repaired and replaced at the official repair point of the mobile phone brand.
The introduction of Mi 13 wireless car charging problem talk here, thank you for taking the time to read the content of the site, more about the millet car wireless charger why can't charge, Mi 13 wireless car charging problem information don't forget to find oh in the site.